Magnetic Mating Interface
Confirm Pin count, contact allocation, magnet arrangement, connector shape, polarity control and mating direction.
A custom 2 pin magnetic charging cable with a compact rectangular molded head, protruding guided mating tongue and two visible contact positions. The electrical Pin Map, polarity, contact type, voltage, current capability, cable length, opposite-end termination and mating dimensions are defined according to the approved project drawing.
The finished assembly must define the magnetic mating component, internal conductor arrangement, cable construction and the opposite-end connection as one complete electrical system.
Confirm Pin count, contact allocation, magnet arrangement, connector shape, polarity control and mating direction.
Define cable length, conductor count, wire specification, shielding requirements, jacket and flexibility.
Select USB, Type-C, DC plug, bare wire, terminal, PCB connection or another customized termination.
Confirm installation space, outlet direction, strain relief, exposed-contact state and user operation.
2 PIN RECTANGULAR MAGNETIC CHARGING CABLE
This 2 pin magnetic charging cable is a complete cable assembly with a compact rectangular molded head, a protruding mating tongue and two visible electrical contact positions.
The two contacts are assigned according to the approved Pin Map. Charging is the confirmed function of this product, while polarity, contact type, voltage, current capability and opposite-end termination are project-specific.
Magnets primarily assist capture and retention. Final position, alignment and seating should be controlled by the visible guide features, mating housing and mechanical geometry rather than by magnetic attraction alone.
The visible charging head uses a rectangular molded housing with a narrower mating tongue extending from the front of the cable head.
Guide or rib features are visible around the mating area. Their exact mechanical function, dimensional tolerances and any polarity-keying role should be confirmed by the approved device-side drawing.
Pin Count Two electrical contact positions
Head Shape Compact rectangular molded housing
Mating Geometry Protruding tongue with visible guide features
Primary Function Project-defined charging interface
The approved drawing should identify Pin 1, viewing direction, positive and return allocation, and the exact position of both electrical contacts.
The cable-side and device-side drawings should use the same viewing reference so the two-contact assignment cannot be mirrored during electrical or mechanical integration.
If the visible guide geometry is intended to control mating orientation or polarity, that function should be defined in the mechanical drawing rather than assumed from product appearance.
The magnetic structure assists the charging head during approach and helps retain the interface after engagement.
Capture force, retention force, separation force and peel force describe different mechanical conditions. The required magnetic behavior should be defined around the device geometry, cable handling and intended release direction.
Final alignment and seating should be controlled by the mating tongue, guide geometry, housing datums and seating surfaces. Magnetic attraction alone should not be treated as proof of a valid electrical connection.
The product image confirms two electrical contact positions, but the spring-loaded contact structure and travel values should be confirmed from the approved drawing.
If spring-loaded pogo contacts are used, working stroke and total travel must be treated as separate parameters. The working stroke defines the intended operating compression, while total travel represents the available mechanical movement.
The mating housing should establish the final mechanical seating condition. Spring contacts should provide electrical contact and controlled compliance rather than act as the primary mechanical hard stop.
Charging-current capability cannot be determined from the two-contact configuration or contact size alone.
Power Source → Opposite-End Termination → Cable Conductors → Magnetic Charging Head → Electrical Contact Interface → Device-Side Contacts → Device PCB → Charging Circuit → Battery / Load
Vdrop = I × Rpath
Ploss = I² × Rpath
Cable length, conductor gauge, termination resistance, contact resistance, mating condition, device-side PCB copper and operating temperature should be evaluated together before a continuous-current rating is released.
Continuous current and peak current should be defined separately when the charging system includes transient or intermittent operating conditions.
Charging is the confirmed function of this cable. USB termination or USB data capability should not be assumed from the existing product name or URL.
If the opposite cable end uses USB-A, USB-C or another standard connector, the exact termination should be defined by the approved cable drawing.
Any data function must be evaluated separately through the complete electrical channel. A two-contact interface does not by itself establish a USB data protocol or supported data rate.
The rectangular magnetic charging head is only one part of the complete cable assembly.
Cable length, conductor count, wire gauge, conductor material, outer jacket, strain relief and opposite-end termination should be defined together with the charging requirements of the device.
USB-A, USB-C, DC plug, terminal, bare wire or another custom interface should only be stated after the approved cable drawing confirms the actual configuration.
| Specification | Details |
|---|---|
| Product Type | 2 Pin Rectangular Magnetic Charging Cable |
| Pin Count | 2 Pin |
| Primary Function | Charging |
| Charging Head Shape | Rectangular |
| Mating Structure | Protruding Mating Tongue with Visible Guide Features |
| Contact Arrangement | Two Offset Contact Positions |
| Contact Type | To Be Confirmed |
| Cable-Side Interface | Integrated Molded Magnetic Head |
| Magnetic Function | Capture + Retention |
| Final Position / Alignment | Controlled by Mechanical Guide and Mating Geometry |
| Pin Map | Defined by Approved Drawing |
| Charging Function | Confirmed |
| Data / Signal Function | To Be Confirmed |
| USB Termination | To Be Confirmed |
| Cable Length | Project-Specific |
| Voltage | Project-Specific |
| Continuous Current | To Be Confirmed |
| Peak Current | To Be Confirmed |
| Current Capability | Validate Complete Conductive Path |
| Working Stroke | To Be Confirmed |
| Total Travel | To Be Confirmed |
| Magnetic Retention | Project-Specific |
| Device-Side Interface | To Be Confirmed |
| Material / Plating | To Be Confirmed |
| Cycle Life | To Be Confirmed |
| Operating Temperature | To Be Confirmed |
| IP Rating | Not Claimed Without Complete Assembly Validation |
CTP can review the complete two-pin rectangular magnetic charging cable around the customer’s electrical, cable and mechanical requirements.
This rectangular 2 pin magnetic charging cable can be evaluated for devices requiring a detachable charging connection and a mechanically guided compact mating interface.
Final application suitability depends on the approved Pin Map, electrical load, mating geometry, cable construction, magnetic behavior and environmental requirements.
Environmental capability should be validated for the complete cable assembly and installed mating interface under defined test conditions.
Corrosion behavior, mating-cycle capability, cable bending life and operating-temperature performance depend on the actual contact material, surface finish, cable construction and application conditions.
The rectangular housing and guide structure do not establish a waterproof rating. An IP rating should only be claimed when the complete mating and sealing assembly has been defined and tested.
It is a magnetic charging cable assembly with two electrical contact positions and a compact rectangular cable head. This version also uses a protruding mating tongue with visible guide features.
Their exact functions and polarity are defined by the approved Pin Map. Charging is confirmed, but positive and return allocation should be specified on the project drawing.
The product image confirms two electrical contact positions, but the spring-loaded structure and travel parameters should be confirmed from the approved contact drawing.
Current capability is project-specific and must be validated through the complete conductive path, including the cable conductors, termination, magnetic interface, device-side contacts and charging circuit.
Magnets primarily assist capture and retention. Final position and alignment should be established by the mating tongue, guide features and mechanical housing geometry.
USB should not be assumed from the existing product name or URL. The opposite-end termination must be confirmed by the approved cable drawing.
USB data capability should not be inferred from the pin count. Any data function must be defined and validated through the complete electrical architecture.
Yes. Cable length, conductor construction, strain relief and opposite-end termination can be defined according to the approved project requirements.
No IP rating should be assumed from the housing or magnetic interface. Environmental protection depends on the complete mating and sealing structure and must be validated at assembly level.
Provide the Pin Map, polarity, voltage, continuous and peak current, cable length, wire gauge, opposite-end termination, charging-head dimensions, mating geometry, contact requirements, magnetic requirements and available 2D or 3D drawings.
CUSTOM 2 PIN MAGNETIC CHARGING CABLE DEVELOPMENT
Send CTP your 2-pin Pin Map, polarity, voltage, continuous and peak current, cable length, wire gauge, opposite-end termination, mating-head dimensions, contact requirements, magnetic requirements and device-side drawings. Our engineering team can review the complete charging interface before quotation and sample development. Request Custom Quote & Samples
This product page presents a CTP magnetic cable assembly configuration for engineering reference. Final dimensions, electrical ratings, materials, magnet structure, sealing level and reliability targets are not universal values; they are confirmed against the approved drawing, installation condition and model-specific validation plan.
CTP reviews the application and prepares a drawing or specification for approval before sample production. Test scope, acceptance criteria and report format should identify the model, sample status, method, conditions, result and review date.
Yes. Customization can cover geometry, contact layout, materials, cable construction, magnetic structure, sealing and appearance. Feasibility depends on the application and approved specification.
No. Current, voltage, resistance, temperature rise and ingress-protection claims apply only to the identified model and stated test conditions.
Timing is confirmed after the drawing, materials, tooling, sample quantity, validation scope and production requirements have been reviewed.
A reference product image is not enough to define a cable assembly. Confirm the following information before drawing, sampling or quotation review.
The exact project route depends on whether an existing product can be used, modified or requires a new cable assembly design.
Confirm product scope, Pin Map, cable length, termination, quantity and application conditions.
Match magnetic contacts to conductors, source-side wiring and device-side functions.
Confirm dimensions, outlet direction, cable construction and required sample configuration.
Review electrical, mechanical and environmental conditions before production approval.
Submit the magnetic-end structure, electrical functions, cable length, conductor requirements, opposite-end interface, installation space and available drawings for project review.
Review related cable assemblies by contact count, shape, termination and project supply scope.
